Teradek, Bolt 4K MAX 12G-SDI/HDMI Wireless TX/RX Delux – TE-10-2120-G

The Bolt 4K MAX Wireless TX/RX Deluxe Kit from Teradek is a wireless transmitter and receiver set designed to transmit and receive signals up to 5000′ away using the included panel antenna array. This kit allows you to transmit uncompressed 4K60 video with less than 1 ms of delay. The transmitter, receiver, and panel each include a V-mount battery plate.

The included transmitter can send video signals to six separate receivers, and is compatible with all the Bolt 4K models. It features 12G-SDI, HDMI 2.0, and a 12G-SDI loop-output. The receiver unit features two 12G-SDI and an HDMI 2.0 connector. It also supports HDR workflows, 10-bit 4:22 via 12G-SDI, and 8-bit 4:4:4 via HDMI. The set also includes power, HDMI, USB, and SDI cables, mounting gear, a tool set, and a hard-shell SKB carry case.

Teradek Bolt 4K MAX 12G-SDI/HDMI Wireless Transmitter (V-Mount)

Use the Bolt 4K MAX 12G-SDI/HDMI Wireless Transmitter from Teradek with Gold mount battery plate to transmit 4K60 video signals from a 12G-SDI or HDMI input to any Bolt 4K series receiver with less than 1 ms of latency. The transmitter unit can be secured to a camera or other SDI/HDMI video source via a built-in 1/4″-20 threaded hole as well as two M3 threaded holes. The four included antennas provide a powerful signal for up to a 3000′ line of sight, and with the 4K Array Panel antenna you can transmit up to 5000′ line of sight.

The transmitter supports cross conversion from HDMI input to SDI loop output. It also supports HDR workflows, 10-bit 4:2:2 via 12G-SDI, and 8-bit 4:4:4 via HDMI. Its bright LED screen shows current settings and frequencies, and the transmitter can also connect with the Bolt app for iOS via Bluetooth for configuration.

Power can be provided using a Gold mount battery or with the integrated 2-pin connector and included AC adapter. The transmitter supports up to six receivers, and it can operate up to six transmitters in the same area along with Wi-Fi or 5 GHz appliances with the help of the noise rejection feature. It also features a built-in AES-256 encryption with RSA-1024 key exchange.

– HDMI and 12G-SDI inputs, with 12G-SDI loop-through output

– 3000′ line-of-sight range, 5000′ line-of-sight range with separately available 4K Array panel antenna

– Compatible with any Bolt 4K series receiver

– Up to 48 kHz 24-bit PCM embedded audio supported

– SDI ancillary data support for metadata, timecode, and start/stop flags from certain camera manufacturers

– 1/4″-20 and M3 mounting points

– 2-pin LEMO-type power input

– Built-in display with joystick navigation

– Micro-USB port for upgrades

Teradek Bolt 4K MAX 12G-SDI/HDMI Wireless Receiver (V-Mount)

Use the Bolt 4K MAX 12G-SDI/HDMI Wireless Receiver from Teradek with a V-mount plate to receive visually lossless 4K60 video signals from any Bolt 4K series transmitter with less than 1 ms of latency and send them out two 12G-SDI outputs or one HDMI output. The receiver unit can be secured to a camera or other SDI/HDMI video source via built-in 1/4″-20 or 3/8″-16 threaded holes. The five included antennas provide a powerful signal that can receive from up to a 3000′ line of sight.

The receiver supports cross conversion from HDMI input to SDI loop output. It also supports HDR workflows, 10-bit 4:22 via 12G-SDI, and 8-bit 4:4:4 via HDMI. Its bright LED screen shows current settings and frequencies, and the transmitter can also connect with the Bolt app for iOS via Bluetooth for configuration.

Power can be provided using the integrated 2-pin connector with the included AC adapter or with a V-mount battery. A Bolt 4K transmitter supports up to six receivers, and it can operate up to six transmitters with receivers in the same area with Wi-Fi or 5 GHz appliances with the help of the noise rejection feature. It also features built-in AES-256 encryption with RSA-1024 key exchange to protect your video from prying eyes.

– Two 12G-SDI outputs and one HDMI output

– 3000′ line-of-sight range

– Compatible with any Bolt 4K series transmitter

– Up to 48 kHz 24-bit PCM embedded audio supported

– SDI ancillary data support for metadata, timecode, and start/stop flags from certain camera manufacturers

– 1/4″-20 and 3/8″-16 mounting points

– 2-pin LEMO-type power input

– Built-in display with joystick navigation

– Micro-USB port for upgrades

Wooden Camera Ultra Arm Mini Monitor Mount (1/4″-20 to 3/8″-16)

The 1/4″-20 to 3/8″-16 Ultra Arm Mini Monitor Mount from Wooden Camera is a robust and compact articulating arm with 25mm ball joints. Approximately 5″ in length from end to end, the Ultra Arm Mini is designed for keeping a monitor or other accessory close to the camera while providing the full range of ball joint articulation. A lever in the center locks both ball joints, and the mounting points on the ends attach to your gear easily at the turn of integrated tightening knobs. Two locating pins are included that can be user-installed on the 3/8″-16 end to convert it to an ARRI Accessory Mount compatible end. Both ends feature rubber pads for more secure support.

The Ultra Arm system is interchangeable. Wooden Camera offers a variety of optional end points that install into the ball sockets of the arm. These include NATO clamps, NATO rails, shoe mounts, super clamps, and extensions to add between two of these arms. There is even a Preston mounting bracket. Additionally, the system is compatible with many third-party 25mm ball mount systems.

– Full-range ball joint articulation

– Integrated tightening knobs

– Rubber pads

– Interchangeable end points support optional NATO clamps, NATO rails, shoe mounts, super clamps, length extensions, and more (see Accessories tab)

– Also compatible with third-party 25mm ball mount systems

Specifications

Bolt 4K MAX 12G-SDI/HDMI Wireless Transmitter (V-Mount)

Wireless

Wireless Range

3000′ / 914.4 m (Line-of-Sight)

No. of Channels

14 (40 MHz)

Channel Bandwidth

40 MHz

Frequency Range

US: 5.19 to 5.23 GHz

US: 5.75 to 5.79 GHz

US: 5.27 to 5.67 GHz

Latency

< 1 ms

RF Power

19 dBm

Wi-Fi

5 GHz

Wireless Video Compression

Uncompressed

Interfaces

Antenna Ports

4 x RP-SMA Female

Video Connectors

1 x BNC (12G-SDI) Input

1 x HDMI (HDMI 1.4 / HDMI 2.0) Input

1 x BNC (12G-SDI) Loop Output

Other I/O

1 x USB Micro-B USB 2.0 Input

Embedded Audio

HDMI: 2-Channel

SDI: 2-Channel

Encryption

256-Bit AES

Format Support

Broadcast System Compatibility

NTSC, PAL

Video Format

SDI/BNC:

1080p/DCI 4K 4:2:2 YCC 10-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps

1080PsF 4:2:2 YCC 10-Bit at 23.98, 24, 25, 29.97, 30 fps

1080i/720p 4:2:2 YCC 10-Bit at 50, 59.94, 60 fps

576p/576i/480p/480i

HDMI:

1080p/DCI 4K 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps

1080PsF 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30 fps

1080i/720p 4:4:4 RGB 8-Bit at 50, 59.94, 60 fps

576p/576i/480p/480i

Audio Format

2-Channel 24-Bit 48 kHz PCM Audio

Timecode

Yes

Power

Built-In Battery

None

Battery Support

1 x V-Mount

Power Connector

1 x 2-Pin LEMO (6 to 28 VDC) Input

Power Consumption

(20 W)

Environmental

Operating Temperature

32 to 104°F / 0 to 40°C

General

Mounting

1 x 1/4″-20 Female

2 x M3 Female

Materials

Aluminum

Dimensions

5.2 x 3.58 x 1.06″ / 132 x 91 x 27 mm

Weight

12.7 oz / 360 g

14.39 oz / 408 g (With 4 x Antennas)

Bolt 4K MAX 12G-SDI/HDMI Wireless Receiver (V-Mount)

Wireless

Wireless Range

3000′ / 914.4 m (Line-of-Sight)

No. of Channels

14 (40 MHz)

Frequency Range

US: 5.19 to 5.23 GHz

US: 5.75 to 5.79 GHz

US: 5.27 to 5.67 GHz

Latency

< 1 ms

RF Power

17 dBm

Wi-Fi

5 GHz

Wireless Video Compression

Uncompressed

Interfaces

Antenna Ports

5 x RP-SMA Female

Video Connectors

2 x BNC (12G-SDI) Output

1 x HDMI (HDMI 1.4 / HDMI 2.0) Input

Other I/O

1 x USB Micro-B USB 2.0 Input

Embedded Audio

HDMI: 2-Channel

SDI: 2-Channel

Encryption

256-Bit AES